Hej og tak for de mange svar.
Benny Amorsen wrote:
>>>>>> "K" == Klaus <dont-spam-me@kolle.com> writes:
>
> K> Hej, jeg har slåsset med at få wireles til at fungere i Fedora C6,
> K> men uden held.
>
> K> Det indbyggede kort er Intels 2100 - derfor har jeg installeret
> K> ipw2100 driveren vha. yum (fra Livna). Men jeg får hver gang jeg
> K> forsøger at starte eth1, som er mapningen for netkortet en fejl:
> K> "Error for wireless request: "Set Frequency" (8B04): SET failed on
> K> device eth1; Operation not supported.
>
> Er du HELT sikker på det er en 2100? Den model kan også fås med et
> a/b/g-kort, og det er efter sigende ikke nemt at få i gang.
Så vidt jeg har kunnet finde ud af er det et std. 2100 b kort.
>
> Derudover skal du ikke installere driveren fra livna, kun firmwaren.
> Det er i al fald det jeg har gjort på en nx8220.
Jeg har /lib/firmware/ipw2100-1.2.1 mappe og samme sted ipw2100-1.3.fw +
nogle andre. Gad vide om det er her problemet ligger. En tidligere
poster nævnte noget om at flytte firmware et trin tilbage i strukturen.
>
> Hvad siger lsmod|grep ipw? dmesg? iwconfig -a?
Kommer her (advarsel lang)
>iwconfig
eth1 unassociated ESSID:"qwerty" Nickname:"klaus-laptop"
Mode:Managed Channel=0 Access Point: Not-Associated
Bit Rate=0 kb/s Tx-Power:16 dBm
Retry limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
>lsmod|grep ipw
ipw2100 74609 0
ieee80211 36233 1 ipw2100
>dmesg
Linux version 2.6.19-1.2895.fc6
(brewbuilder@hs20-bc1-5.build.redhat.com) (gcc version 4.1.1 20070105
(Red Hat 4.1.1-51)) #1 SMP Wed Jan 10 18:32:37 EST 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffd0000 (usable)
BIOS-e820: 000000001ffd0000 - 000000001fff0c00 (reserved)
BIOS-e820: 000000001fff0c00 - 000000001fffc000 (ACPI NVS)
BIOS-e820: 000000001fffc000 - 0000000020000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
Using x86 segment limits to approximate NX protection
Entering add_active_range(0, 0, 131024) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 131024
HighMem 131024 -> 131024
early_node_map[1] active PFN ranges
0: 0 -> 131024
On node 0 totalpages: 131024
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 991 pages used for memmap
Normal zone: 125937 pages, LIFO batch:31
HighMem zone: 0 pages used for memmap
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP (v000 COMPAQ ) @ 0x000faa50
ACPI: RSDT (v001 HP CPQ0860 0x15080320 CPQ 0x00000001) @ 0x1fff0c84
ACPI: FADT (v002 HP CPQ0860 0x00000002 CPQ 0x00000001) @ 0x1fff0c00
ACPI: SSDT (v001 COMPAQ CPQGysr 0x00001001 MSFT 0x0100000e) @ 0x1fff5b28
ACPI: DSDT (v001 HP nx7000 0x00010000 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
Allocating PCI resources starting at 30000000 (gap: 20000000:e0000000)
Detected 598.093 MHz processor.
Built 1 zonelists. Total pages: 130001
Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (01425000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c07f6000 soft=c07d6000
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 512016k/524096k available (2177k kernel code, 11572k reserved,
1108k data, 240k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xffc55000 - 0xfffff000 (3752 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB)
lowmem : 0xc0000000 - 0xdffd0000 ( 511 MB)
.init : 0xc0795000 - 0xc07d1000 ( 240 kB)
.data : 0xc0620657 - 0xc07358f4 (1108 kB)
.text : 0xc0400000 - 0xc0620657 (2177 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1196.91 BogoMIPS
(lpj=598457)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: a7e9f9bf 00000000 00000000 00000000
00000180 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: After all inits, caps: a7e9f1bf 00000000 00000000 00000040 00000180
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
ACPI: Core revision 20060707
ACPI: setting ELCR to 0200 (from 0c20)
CPU0: Intel(R) Pentium(R) M processor 1500MHz stepping 05
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
sizeof(vma)=84 bytes
sizeof(page)=32 bytes
sizeof(inode)=424 bytes
sizeof(dentry)=144 bytes
sizeof(ext3inode)=600 bytes
sizeof(buffer_head)=56 bytes
sizeof(skbuff)=172 bytes
sizeof(task_struct)=1376 bytes
checking if image is initramfs... it is
Freeing initrd memory: 2267k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf031f, last bus=3
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [C046] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.C046] bus is 0
PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 1100-113f claimed by ICH4 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
PCI: Bus #03 (-#06) is hidden behind transparent bridge #02 (-#03) (try
'pci=assign-busses')
Please report the result to linux-kernel to fix this permanently
ACPI: PCI Interrupt Routing Table [\_SB_.C046._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C046.C047._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.C046.C058._PRT]
ACPI: Power Resource [C18D] (on)
ACPI: Power Resource [C195] (on)
ACPI: Power Resource [C19C] (on)
ACPI: Power Resource [C1A6] (on)
ACPI: PCI Interrupt Link [C0C2] (IRQs 5 *10)
ACPI: PCI Interrupt Link [C0C3] (IRQs 5 *10)
ACPI: PCI Interrupt Link [C0C4] (IRQs *5 10)
ACPI: PCI Interrupt Link [C0C5] (IRQs *5 10)
ACPI: PCI Interrupt Link [C0C6] (IRQs 5 10) *0, disabled.
ACPI: PCI Interrupt Link [C0C7] (IRQs 5 10) *11
ACPI: PCI Interrupt Link [C0C8] (IRQs 5 10) *0, disabled.
ACPI: PCI Interrupt Link [C0C9] (IRQs *5 10)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: 00:0d: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0d: ioport range 0x1000-0x107f could not be reserved
pnp: 00:0d: ioport range 0x1100-0x113f has been reserved
pnp: 00:0d: ioport range 0x1200-0x121f has been reserved
PCI: Bridge: 0000:00:01.0
IO window: 3000-3fff
MEM window: 90400000-904fffff
PREFETCH window: 98000000-9fffffff
PCI: Bus 3, cardbus bridge: 0000:02:04.0
IO window: 00002800-000028ff
IO window: 00002c00-00002cff
PREFETCH window: 30000000-31ffffff
MEM window: 34000000-35ffffff
PCI: Bridge: 0000:00:1e.0
IO window: 2000-2fff
MEM window: 90000000-903fffff
PREFETCH window: 30000000-31ffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt Link [C0C4] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [C0C4] -> GSI 5 (level, low)
-> IRQ 5
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 6, 327680 bytes)
TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1169754556.311:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
ksign: Installing public key data
Loading keyring
- Added public key 5FA3A1EB952EC724
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 855PM Chipset.
agpgart: AGP aperture is 256M @ 0xb0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS2 at I/O 0x3e8 (irq = 3) is a 16550A
00:03: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt Link [C0C3] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [C0C3] -> GSI 10 (level,
low) -> IRQ 10
ACPI: PCI interrupt for device 0000:00:1f.6 disabled
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [C0C4] -> GSI 5 (level, low)
-> IRQ 5
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x4c40-0x4c47, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x4c48-0x4c4f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: ST9160821A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: HL-DT-STCD-RW/DVD DRIVE GCC-4241N, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 512KiB
hda: 312581808 sectors (160041 MB) w/8192KiB Cache, CHS=19457/255/63,
UDMA(100)
hda: cache flushes supported
hda: hda1 hda2
ide-floppy driver 0.99.newide
Yenta: CardBus bridge found at 0000:02:04.0 [0e11:0860]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.0, mfunc 0x001c1112, devctl 0x44
Yenta: ISA IRQ mask 0x08d8, PCI irq 5
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#02) from #03 to #06
pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff
cs: IO port probe 0x2000-0x2fff: clean.
pcmcia: parent PCI bridge Memory window: 0x90000000 - 0x903fffff
pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x31ffffff
usbcore: registered new interface driver libusual
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:C1A3,PNP0f13:C1A4] at 0x60,0x64 irq 1,12
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP bic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 240k freed
Write protecting the kernel read-only data: 400k
Time: tsc clocksource has been installed.
Time: acpi_pm clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [C0C2] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [C0C2] -> GSI 10 (level,
low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 10, io base 0x000048c0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [C0C5] enabled at IRQ 5
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [C0C5] -> GSI 5 (level, low)
-> IRQ 5
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 5, io base 0x000048e0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [C0C4] -> GSI 5 (level, low)
-> IRQ 5
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 5, io base 0x00004c00
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-1: new low speed USB device using uhci_hcd and address 2
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [C0C9] enabled at IRQ 5
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [C0C9] -> GSI 5 (level, low)
-> IRQ 5
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 5, io mem 0xa0000000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
Synaptics Touchpad, model: 1, fw: 5.9, id: 0x236eb3, caps: 0x904713/0x10008
input: SynPS/2 Synaptics TouchPad as /class/input/input1
SCSI subsystem initialized
libata version 2.00 loaded.
device-mapper: ioctl: 4.10.0-ioctl (2006-09-14) initialised:
dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
usb 1-1: new low speed USB device using uhci_hcd and address 3
usb 1-1: configuration #1 chosen from 1 choice
input: HID 062a:0000 as /class/input/input2
input: USB HID v1.10 Mouse [HID 062a:0000] on usb-0000:00:1d.0-1
usb 3-2: new full speed USB device using uhci_hcd and address 2
usb 3-2: configuration #1 chosen from 1 choice
SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks
audit(1169754565.404:2): selinux=0 auid=4294967295
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: HCI USB driver ver 2.9
usbcore: registered new interface driver hci_usb
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
NET: Registered protocol family 23
Detected unconfigured Compaq x1000 family SMSC IrDA chip,
pre-configuring device.
Setting up Intel 82801 controller and SMSC device
found SMC SuperIO Chip (devid=0x5a rev=00 base=0x002e): LPC47N227
smsc_superio_flat(): fir: 0x2f8, sir: 0x2e8, dma: 03, irq: 7, mode: 0x0e
SMsC IrDA Controller found
IrCC version 2.0, firport 0x2f8, sirport 0x2e8 dma=3, irq=7
No transceiver found. Defaulting to Fast pin select
IrDA: Registered device irda0
wbsd: Winbond W83L51xD SD/MMC card interface driver, 1.6
wbsd: Copyright(c) Pierre Ossman
pnp: Device 00:02 activated.
mmc0: W83L51xD id 7112 at 0x248 irq 6 dma 2 PnP
8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [C0C3] -> GSI 10 (level,
low) -> IRQ 10
eth0: RTL-8139C+ at 0xe099c000, 00:02:3f:65:94:fe, IRQ 10
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [C0C2] -> GSI 10 (level,
low) -> IRQ 10
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10]
MMIO=[90200000-902007ff] Max Packet=[1024] IR/IT contexts=[4/8]
8139too Fast Ethernet driver 0.9.28
ieee80211_crypt: registered algorithm 'NULL'
ACPI: PCI Interrupt 0000:00:1f.3[B] -> Link [C0C3] -> GSI 10 (level,
low) -> IRQ 10
input: PC Speaker as /class/input/input3
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023f393800254c]
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [C0C3] -> GSI 10 (level,
low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1f.5 to 64
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation
<jketreno@linux.intel.com>
AC'97 0 analog subsections not ready
ipw2100: Intel(R) PRO/Wireless 2100 Network Driver, git-1.2.2
ipw2100: Copyright(c) 2003-2006 Intel Corporation
intel_rng: FWH not detected
intel8x0_measure_ac97_clock: measured 50207 usecs
intel8x0: clocking to 48000
ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [C0C5] -> GSI 5 (level, low)
-> IRQ 5
ipw2100: Detected Intel PRO/Wireless 2100 Network Connection
cs: IO port probe 0x100-0x3af: excluding 0x140-0x14f 0x200-0x20f
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
Floppy drive(s): fd0 is 1.44M
IRQ handler type mismatch for IRQ 6
current handler: wbsd
[<c040566b>] dump_trace+0x69/0x1b6
[<c04057d0>] show_trace_log_lvl+0x18/0x2c
[<c0405dc6>] show_trace+0xf/0x11
[<c0405ec3>] dump_stack+0x15/0x17
[<c044e991>] setup_irq+0x179/0x199
[<c044ea2d>] request_irq+0x7c/0x98
[<e0b4c666>] init_module+0x537/0xe04 [floppy]
[<c043ee90>] sys_init_module+0x17fc/0x19a7
[<c0404057>] syscall_call+0x7/0xb
[<00adf402>] 0xadf402
=======================
floppy0: Unable to grab IRQ6 for the floppy driver
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.00 (08-Oct-2006)
iTCO_wdt: Found a ICH4-M TCO device (Version=1, TCOBASE=0x1060)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [C0C3] -> GSI 10 (level,
low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1f.6 to 64
Floppy drive(s): fd0 is 1.44M
IRQ handler type mismatch for IRQ 6
current handler: wbsd
[<c040566b>] dump_trace+0x69/0x1b6
[<c04057d0>] show_trace_log_lvl+0x18/0x2c
[<c0405dc6>] show_trace+0xf/0x11
[<c0405ec3>] dump_stack+0x15/0x17
[<c044e991>] setup_irq+0x179/0x199
[<c044ea2d>] request_irq+0x7c/0x98
[<e0ae1666>] init_module+0x537/0xe04 [floppy]
[<c043ee90>] sys_init_module+0x17fc/0x19a7
[<c0404057>] syscall_call+0x7/0xb
[<00fa0402>] 0xfa0402
=======================
floppy0: Unable to grab IRQ6 for the floppy driver
lp0: using parport0 (interrupt-driven).
lp0: console ready
sonypi: Sony Programmable I/O Controller Driver v1.26.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [C0C2] -> GSI 10 (level,
low) -> IRQ 10
[drm] Initialized radeon 1.25.0 20060524 on minor 0
ACPI: AC Adapter [C134] (off-line)
ACPI: Battery Slot [C11F] (battery present)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [C1BE]
ACPI: Lid Switch [C136]
ACPI: Video Device [C0D0] (multi-head: yes rom: no post: no)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.5 loaded
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x54 { AbortedCommand
LastFailedSense=0x05 }
ide: failed opcode was: unknown
hdc: packet command error: status=0x51 { DriveReady SeekComplete Error }
hdc: packet command error: error=0x54 { AbortedCommand
LastFailedSense=0x05 }
ide: failed opcode was: unknown
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 1048568k swap on /dev/VolGroup00/LogVol01. Priority:-1 extents:1
across:1048568k
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (4094 buckets, 32752 max) - 232 bytes per conntrack
process `sysctl' is using deprecated sysctl (syscall)
net.ipv6.neigh.lo.base_reachable_time; Use
net.ipv6.neigh.lo.base_reachable_time_ms instead.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
ADDRCONF(NETDEV_UP): eth1: link is not ready
eth0: no IPv6 routers present
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
Bluetooth: HIDP (Human Interface Emulation) ver 1.1
ttyS0: LSR safety check engaged!
ttyS2: LSR safety check engaged!
mtrr: 0x98000000,0x8000000 overlaps existing 0x98000000,0x4000000
mtrr: 0x98000000,0x8000000 overlaps existing 0x98000000,0x4000000
mtrr: 0x98000000,0x8000000 overlaps existing 0x98000000,0x4000000
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[drm] Setting GART location based on new memory map
[drm] Loading R200 Microcode
[drm] writeback test succeeded in 2 usecs
/Klaus
|